vertical system
|
|
analog (prolink input) bandwidth @ 50 ω (-3 db)
|
13 ghz (≥10 mv/div)
|
|
analog (probus input) bandwidth @ 50 ω (-3 db)
|
3.5 ghz (≥10 mv/div)
|
|
analog (probus input) bandwidth @ 1 mω (-3 db)
|
500 mhz (typical, ≥2 mv/div)
|
|
rise time (10–90%)
|
32.5 ps (test limit, flatness mode)
|
|
rise time (20–80%)
|
24.5 ps (flatness mode)
|
|
bandwidth limiters
|
20 mhz, 200 mhz, 1 ghz, 4 ghz, 6 ghz, 8 ghz
|
|
input impedance
|
prolink inputs: 50 ω+/-2% for ≤100 mv/div, 50 ω+/-3% for >100 mv/div
probus inputs: 50 ω+/-2% or 1 mω||16pf, 10 mω || 11 pf with supplied probe
|
|
input coupling
|
prolink inputs - 50 ω: dc, gnd
probus inputs - 1 mω: ac, dc, gnd; 50 ω: dc, gnd
|
|
maximum input voltage
|
50 ω (prolink): ±2 vmax@≤100mv/div, 5.5vrms@>100mv/div
50 ω (probus): ±5 vmax, 3.5 vrms
1 mω (probus): 250 v max. (peak ac: < 10 khz + dc)
|
|
channel-channel isolation
|
dc to 10 ghz: 50 db (>315:1)
10 to 15 ghz: 46 db (>200:1)
15 to 20 ghz: 40 db (>100:1)
(for any two prolink input channels, same or different v/div settings, typical)
|
|
sensitivity
|
50 ω (prolink): 2 mv–1 v/div, fully variable (2-9.9 mv/div via zoom)
50 ω (probus): 2 mv–1 v/div, fully variable; 1 mω (probus): 2 mv–10 v/div, fully variable
|
|
dc vertical gain accuracy (gain component of dc accuracy)
|
+/-1% f.s. (typical), offset at 0v; +/-1.5% f.s. (test limit), offset at 0v
|
|
offset range
|
50 ω (prolink):
±500 mv @ 2–100 mv/div
±4 v @ >100 mv/div -1 v/div
50 ω (probus):
±750 mv @ 2–100 mv/div
±4 v @ >100 mv/div -1 v/div
1 mω:
±1v @ 2–140 mv/div
±10v @ 142mv-1.40v/div
|
|
dc vertical offset accuracy
|
+/-(1.5% of offset setting + 1mv) (test limit)
|
|
|
horizontal system
|
|
timebases
|
internal timebase common to 4 input channels
|
|
time/division range
|
20 ps/div–128 s/div (real-time mode: 20 ps/div - 64 s/div; ris mode: 20 ps/div - 10 ns/div; roll mode: 100 ms/div up to 128 s/div), depending on memory length
|
|
clock accuracy
|
< 1 ppm + (aging of 0.5ppm/yr from last calibration)
|
|
time interval accuracy
|
< 0.06 / sr + (clock accuracy* reading) (rms)
|
|
jitter noise floor
|
for acq. length ≤10μs: 250 fsrms (tie, typical)
for acq. length >10μs: 300 fsrms (tie, typical)
|
|
trigger and interpolator jitter
|
<0.1 ps rms (typical, software assisted), 2 ps rms (typical, hardware),
|
|
channel-channel deskew range
|
±9 x time/div. setting or 25 ns max. (whichever is larger), each channel
|
|
external timebase reference (input)
|
10 mhz; 50 ω impedance, applied at the rear input
|
|
external timebase reference (output)
|
10 mhz; 50 ω impedance, output at the rear
|
|
|
acquisition system
|
|
single-shot sample rate/ch
|
40 gs/s on 4 ch
(80 gs/s on 2 ch using optional wm8zi-2x80gs external interleaving device)
|
|
random interleaved sampling (ris)
|
200 gs/s for repetitive signals (20 ps/div to 10 ns/div)
|
|
maximum trigger rate
|
1,000,000 waveforms/second (in sequence mode, up to 4 channels)
|
|
memory options (4 ch / 2 ch / 1ch)
|
m-64 option:
64m / 64m / 64m
(15,000)
l-128 option:
128m / 128m / 128m
(15,000)
vl-256 option:
256m / 256m / 256m
(15,000)
note: on all memory options, wm8zi-2x80gs external interleaving device permits 80 gs/s on 1 or 2ch with twice the memory)
|
|
standard memory (4 ch / 2 ch / 1ch) (number of segments)
|
32 m / 32 m / 32 m
(memory and sample rate can be doubled in 1 or 2 ch mode with use of wm8zi-2x80gs external interleaving device)
(3500)
|
|
|
acquisition processing
|
|
averaging
|
summed averaging to 1 million sweeps; continuous averaging to 1 million sweeps
|
|
enhanced resolution (eres)
|
from 8.5 to 11 bits vertical resolution
|
|
envelope (extrema)
|
envelope, floor, or roof for up to 1 million sweeps
|
|
interpolation
|
linear or sin x/x
|
|
|
triggering system
|
|
modes
|
normal, auto, single, and stop
|
|
sources
|
any input channel, aux, aux/10, line, or fast edge. slope and level unique to each source (except line trigger)
|
|
coupling mode
|
dc, ac, hfrej, lfrej
|
|
pre-trigger delay
|
0–100% of memory size (adjustable in 1% increments of 100 ns)
|
|
post-trigger delay
|
0–10,000 divisions in real time mode, limited at slower time/div settings or in roll mode
|
|
hold-off by time
|
from 2 ns up to 20 s or from 1 to 99,999,999 events
|
|
internal trigger range
|
±4.1 div from center
|
|
trigger sensitivity with edge trigger (ch 1–4) probus inputs
|
2 div @ < 3.5 ghz,
1.5 div @ < 1.75 ghz,
1.0 div @ < 200 mhz,
(for dc coupling, ≥ 10 mv/div, 50 ω )
|
|
trigger sensitivity with edge trigger (ch 1–4) prolink inputs
|
3 div @ < 13 ghz,
1.5 div @ < 3 ghz,
1.0 div @ < 200 mhz,
(for dc, ac, lfrej coupling, ≥ 10 mv/div, 50 ω )
|
|
external trigger sensitivity, (edge trigger)
|
2 div @ < 1 ghz,
1.5 div @ < 500 mhz,
1.0 div @ < 200 mhz,
(for dc coupling)
|
|
external trigger input range
|
aux (±0.4 v); aux/10 (±4 v)
|
|
max. trigger frequency, smart trigger
|
2.0 ghz @ ≥ 10 mv/div (minimum triggerable width 200 ps)
|
|
|
basic triggers
|
|
edge
|
triggers when signal meets slope (positive, negative, or either) and level condition.
|
|
window
|
triggers when signal exits a window defined by adjustable thresholds
|
|
tv-composite video
|
triggers ntsc or pal with selectable line and field; hdtv (720p, 1080i, 1080p) with selectable frame rate (50 or 60 hz) and line; or custom with selectable fields (1-8), lines (up to 2000), frame rates (25, 30, 50, or 60 hz), interlacing (1:1, 2:1, 4:1, 8:1), or synch pulse slope (positive or negative)
|
|
|
smart triggers
|
|
state or edge qualified
|
triggers on any input source only if a defined state or edge occurred on another input source. holdoff between sources is selectable by time or events.
|
|
qualified first
|
in sequence acquisition mode, triggers repeatably on event b only if a defined pattern, state, or edge (event a) is satisfied in the first segment of the acquisition. holdoff between sources is selectable by time or events.
|
|
dropout
|
triggers if signal drops out for longer than selected time between 1 ns and 20 s.
|
|
pattern
|
logic combination (and, nand, or, nor) of 5 inputs (4 channels and external trigger input). each source can be high, low, or don’t care. the high and low level can be selected independently. triggers at start or end of the pattern.
|
|
|
smart triggers with exclusion technology
|
|
glitch
|
triggers on positive or negative glitches with widths selectable as low as 200ps to 20 s, or on intermittent faults.
|
|
width (signal or pattern)
|
triggers on positive, negative, or both widths with widths selectable as low as 200ps to 20 s, or on intermittent faults.
|
|
interval (signal or pattern)
|
triggers on intervals selectable between 1 ns and 20 s.
|
|
timeout (state/edge qualified)
|
triggers on any source if a given state (or transition edge) has occurred on another source. delay between sources is 1 ns to 20 s, or 1 to 99,999,999 events.
|
|
runt
|
trigger on positive or negative runts defined by two voltage limits and two time limits. select between 1 ns and 20 ns.
|
|
slew rate
|
trigger on edge rates. select limits for dv, dt, and slope. select edge limits between 1 ns and 20 ns.
|
|
exclusion triggering
|
trigger on intermittent faults by specifying the expected behavior and triggering when that condition is not met
|
|
|
cascade (sequence) triggering
|
|
capability
|
arm on "a" event, then trigger on "b" event. or arm on "a" event, then qualify on "b" event, and trigger on "c" event. or arm on “a” event, then qualify on “b” then “c” event, and trigger on “d” event
|
|
types
|
a, b, c, or d event: edge, glitch, width, window, dropout, interval, runt, slew rate, or pattern (analog)
|
|
holdoff
|
holdoff between a and b, b and c, c or d, or any is selectable by time or number of events
|
|
reset
|
reset between a and b, b and c, c and d, or any combination is selectable in time or number of events
|
|
|
high speed serial protocol triggering
|
|
data rates
|
100 mb/s - 2.7 gb/s, 3.0, 3.125 gb/s
|
|
pattern length
|
80 bits, nrz or 8b10b
|
|
clock and data outputs
|
400mvp-p (typical) ac coupled
|
|
clock recovery jitter
|
2 ps rms + 0.3% unit interval rms for prbs data patterns with 50% transition density (typical)
|
|
hardware clock recovery loop bw
|
pll loop bw = fbaud/5500, 100 mb/s to 2.488 gb/s (typical)
|
|
|
color waveform display
|
|
type
|
color 15.3" flat panel tft-active matrix lcd with high resolution touch screen
|
|
resolution
|
wxga; 1280 x 768 pixels.
|
|
number of traces
|
display a maximum of 8 traces. simultaneously display channel, zoom, memory and math traces.
|
|
grid styles
|
auto, single, dual, quad, octal, x-y, single+x-y, dual+x-y
|
|
waveform representation
|
sample dots joined, or sample dots only
|
|
|
processor/cpu
|
|
type
|
intel? coretm 2 quad, 3.0 ghz (or better)
|
|
processor memory
|
8 gb standard
|
|
operating system
|
microsoft windows? 7 professional edition (64-bit)
|
|
real time clock
|
date and time displayed with waveform in hardcopy files. sntp support to synchronize to precision internal clocks.
|
|
|
interface
|
|
remote control
|
via windows automation, or via lecroy remote command set
|
|
network communication standard
|
vxi-11 or vicp, lxi class c (v1.2) compliant
|
|
gpib port (optional)
|
supports ieee – 488.2
|
|
lsib port (optional)
|
supports pcie gen1 x4 protocol with lecroy supplied api
|
|
ethernet port
|
supports 10/100/1000baset ethernet interface (rj45 port)
|
|
usb ports
|
minimum 6 total (incl. 3 front panel) usb 2.0 ports support windows compatible devices
|
|
external monitor port
|
15 pin d-type wxga compatible to support customer-supplied external monitor. dvi connector to support lecroy wpzi-extdisp-15 additional touch screen display accessory. includes support for extended desktop operation with optional lecroy or other second monitor.
|
|
peripheral bus
|
lecroy lbus standard
|
|
|
power requirements
|
|
voltage
|
100–240 vac ±10% at 45-66 hz; 100-120 vac ±10% at 380-420 hz; automatic ac voltage selection, installation category ii
|
|
max. power consumption
|
975 w / 975 va
|
|
|
environmental and safety
|
|
temperature (operating)
|
+5 °c to +40 °c including cd-rw/dvd-rom drive
|
|
temperature (non-operating)
|
–20 °c to +60 °c
|
|
humidity (operating)
|
5% to 80% relative humidity (non-condensing) up to +31 °c. upper limit derates to 50% relative humidity (non-condensing) at +40 °c.
|
|
humidity (non-operating)
|
5% to 95% relative humidity (non-condensing) as tested per mil-prf-28800f
|
|
altitude (operating)
|
up to 10,000 ft. (3048 m) at or below +25 °c
|
|
altitude (non-operating)
|
up to 40,000 ft. (12,192 m)
|
|
random vibration (operating)
|
0.5 grms 5 hz to 500 hz, 15 minutes in each of three orthogonal axes
|
|
random vibration (non-operating)
|
2.4 grms 5 hz to 500 hz, 15 minutes in each of three orthogonal axes
|
|
functional shock
|
20 g peak, half sine, 11 ms pulse, 3 shocks (positive and negative) in each of three orthogonal axes, 18 shocks total
|
|
|
physical dimensions
|
|
dimensions (hwd)
|
14"h x 18.4"w x 15.3"d (355 x 467 x 390 mm)
|
|
weight
|
51.5 lbs. (23.4 kg)
|
|
shipping weight
|
70.0 lbs. (31.8 kg)
|
|
|
certifications
|
|
certifications
|
ce compliant, ul and cul listed; conforms to en 61326, en 61010-1, ul 61010-1 2nd edition, and csa c22.2 no. 61010-1-04
|
|
|
warranty and service
|
|
warranty and service
|
3-year warranty; calibration recommended annually. optional service programs include extended warranty, upgrades, and calibration services.
|
